![sew what pro user manual sew what pro user manual](https://www.manualsdir.com/manuals/646387/30/metalfab-sew-eurodrive-movimot-mmc-page30.png)
It’s basically done the same way as configuring rifle profile.Ĭatridge 1 - In this field just enter the name you'd like to use to identify this cartridge, e.g. The program remembers all settings data and anytime you select a certain rifle profile will bring it up along with scope reticle and ammo profile used last with this combination. Select an entry and configure the profile as needed. To add a rifle, tap the "Change rifle" button at upper left middle screen. Temperature - Temperature at time of zero.
![sew what pro user manual sew what pro user manual](https://i.pinimg.com/236x/e9/5a/83/e95a831a38a350497b52481fce189bca--embroidery-software-embroidery-applique.jpg)
So if you originally zero at 100 meter altitude and then go hunting with that rifle/ammo to 2000 meter altitude, your zero point will be off (how much it will be off depends on how far your zero range was) and iStrelok will account for this.Īltitude - This is your altitude above sea level at time of zero. By enabling this feature you get automatic zero correction when shooting in different conditions. It’s a good practice to toggle the switch to “ON” and input your zero atmospheric conditions. Zero Atmosphere – weather conditions when you zeroed the rifle. Unit can be changed to MRAD(MIL), or by tapping a small blue round button just below click fields and selecting needed unit. 23 and you’ll never have to think of it again.ĭefault click unit is MOA, value is set at ¼ MOA. These fields can also be used to correct for scope turret clicks that aren't quite what they supposed to be. This value and unit is very likely the same as the elevation's turret. Windage click - Same as Elevation Turret, except for your windage turret. It should be labled on your turret or available in your scope's manual. Try to be precise since it has direct impact on calculations accuracy.Įlevation click - This is the amount of adjustment per-click of your elevation turret. Add all 3 resulting numbers together to get your sight height. Last, measure the gap between the bottom of the scope bell and your barrel. Measure the barrel diameter just under or ahead of the scope's bell, also divide by 2. To measure it on firearm with a mounted scope, measure the diameter of the scope bell (on the end, from side to side, not the circumference!) and divide that number by 2. Scope Height - This is the height from the centerline of your bore to the center of your sight. Zero Range - This is the distance to the target that you zeroed your scope at. Rifle 1 - In this field just enter the name you'd like to use to identify this firearm, e.g. Enter the value and be sure to tap “Done” for confirming it. Tapping numerical value fields pops up a convenient NumPad. For entering new data just tap the field you want to change. Rifle Profiles Configuring rifle profileįields are populated with default entries. You can now enter target data and atmospheric conditions and get your shot solution by tapping “ Calculate! ” button. Once you have iStrelok purchased and installed, perform basic steps for initial setup (explained in detail further if you need clarification): Profiles for rifle and ammo data are saved, so all you have to enter for quick solution is range and shooting conditions.
![sew what pro user manual sew what pro user manual](https://i.pinimg.com/236x/4b/c6/eb/4bc6eb9811e4695cec7dbaba013c7eb1--embroidery-software-machine-embroidery.jpg)
Instant holdover is visible on a reticle of your choice from a vast reticle database (more are added with each update). Elevation and windage adjustments are presented in large and easy to see font for your desired correction in MOA, MRAD(same as Mils), inch/cm and clicks. Supports input/output in Imperial and Metric units. IStrelok features a fast ballistic solver based on G1 drag model and has undergone extensive testing since 2001 by hundreds of qualified shooters. It is also resource friendly, so you can use it for many hours in the field without excess drain on device battery.
#SEW WHAT PRO USER MANUAL FULL#
iStrelok is an autonomous software package that once installed, does not require an internet connection to provide full functionality. It will come in handy both to casual and dedicated shooters, allowing fast and confident shot placement at medium range(distances up to 600 yds and further with some tweaking). IStrelok is an efficient and accurate ballistics calculator for the iOS (iPhone, iPod and iPad) with user friendly interface.